Instructions

There are 2 different types of stickers/decals, Cut Vinyl & Printed

HOW TO APPLY “CUT VINYL” STICKERS (single colour with no background)

SMALL STICKERS/DECALS

Each Sticker/Decal will come in 3 layer stuck together, Top layer is the application transfer tape, this is used to hold the message in place, second layer is the actual sticker/decal, bottom layer is the backing sheet to protect the sticky side of the sticker/decal. When you receive your sticker/decal, lay it flat top side up, & firmly wipe a credit card or similar across the top to ensure that the application tape properly adheres to the sticker/decal.

Instructions for small sticker/decals

  1. Ensure that the application surface is clean, use any “White Spirit” do not use house hold cleaners.
  2. Position the image where you want & mark with a pencil or removable pen
  3. Turn the sticker/decal upside down & peel off the backing at a 45 degree angle
  4. Align the sticker/decal & “Lay” the sticker onto the surface moving from left to right, once down use a credit card or similar to press the sticker/decal firmly to the surface, moving from the centre of the sticker out, once done remove the application tape at an a 45 degree angle, if any part of the sticker/decal starts to lift the using your thumb firmly press over the application tape to press onto surface, then continue until its all removed.
  5. Use a soft clean cloth to wipe over, its all done.

LARGE STICKER/DECALS

  1. Ensure that the application surface is clean, use any “White Spirit” do not use house hold cleaners.
  2. Position the image where you want & mark with a pencil or removable pen
  3. Position the sticker/decal where you want to place it, using masking take, tape the top from an edge to half the length of the sticker/decal, repeat on the bottom, only to half the length, you sticker/decal is now held in place.
  4. Half is held, the other half is loose, hold the loose half & strip back the backing sheet to the half that is stuck & cut off that half of the sheet, from the centre of the sticker/decal lay down the exposed sticker, once done then as it is now stuck remove the masking tape, remove the backing sheet & repeat.
  5. Remove the application tape, wipe over with a soft clean cloth & all is done.

PRINTED SMALL STICKERS/DECALS

These are in 2 layers, top is the sticker, bottom is the backing sheet

  1. Ensure that the application surface is clean, use any “White Spirit” do not use house hold cleaners.
  2. Position the image where you want & mark with a pencil or removable pen
  3. Turn the sticker/decal upside down & peel off the backing at a 45 degree angle
  4. Wet your fingers with plain water so that the sticker/decal does not grab your fingers, will not affect the sticky side at all.
  5. Align the sticker/decal & “Lay” the sticker onto the surface moving from left to right, once down use a credit card – EDGE TO BE COVERED WITH A CLOTH SO AS NOT TO SCRATCH THE PRINTED STICKER/DECAL, or similar to press the sticker/decal firmly to the surface, moving from the centre of the sticker out, once done wipe over with a soft cloth.

PRINTED LARGE STICKERS/DECALS

Same as in the Large Sticker/Decals but remember there are only 2 layers, not 3, but all the info is the same.

WET APPLICATIONS

We suggest this is used with all large stickers/decals, this method will not affect the long term adhesive value of the sticker/decal.

The mix is for a 500ml spray bottle 6 drops of dishwashing liquid to the water, a light mist on both the sticky side & the surface is all that is required, this stops the sticker/decal “grabbing “ the application surface, & also it will allow you to “whip up” the sticker/decal area that is laid wrong & to reapply.

Also there are lots of Youtube content on this.